Distance Measuring Using UltraSonic Sensor In LCD Display

Sr Karthiga

6y19.9k21100Article

IoTUltrasonic SensorLCD DisplayDistance Measuring

21 Comments

Join the conversation! Your thoughts help the community grow.

Sr Karthiga10y ago
thank you asfend sir
Asfend Yar10y ago
good
Sr Karthiga10y ago
Thank you santhakumar sir
Santhakumar Munuswamy10y ago
Thanks for nice share
Sr Karthiga10y ago
Thank you vignesh mani sir
Vignesh Mani10y ago
Nice one
Sr Karthiga10y ago
Thank you Mohammed sir
Mohammed Ibrahim10y ago
nice
Sr Karthiga10y ago
Thank you gowtham sir
Gowtham K10y ago
Good One, Thanks for sharing:)
Sr Karthiga10y ago
Thank you shubham sir
Shubham Kumar10y ago
simply interesting
Sibeesh Venu10y ago
Nice Share
Sr Karthiga10y ago
Thank you kumaresh sir
Kumaresh Rajalingam10y ago
Good one SR
Sr Karthiga10y ago
Thank you Mohammed sir
Sr Karthiga10y ago
Thank you santhakumar sir
Sr Karthiga10y ago
Thank you Ankur mistry sir
Mohammed Ibrahim10y ago
nice
Santhakumar Munuswamy10y ago
Thanks for nice article
Ankur Mistry10y ago
Nice share

Introduction

In this article, I will explain how to measure the distance from any object. It can be easily displayed in the LCD Screen. We can use it on the front door to view the distance of people.

Parts of List

Arduino UNO
Ultrasonic Sensor (HC-SR04)
BreadBoard
LCD Screen
HookUp Wires.

Ultrasonic Sensor (HC-SR04)

Figure 1: Ultrasonic Sensor(HC-SR04)

It is used to produce a high-frequency sound effect.
It can measure the signal from the sender to the receiver.
The echo to be determined from the object.

Where ever we can fix the Ultrasonic Sensor(HC-SR04)

Hospital for medicine
Industry
Home etc.

LCD Screen

Figure 2: LCD Screen

LCD is Liquid Crystal Display (LCD).
It can have the flat-panel or the electronic display
It is used in hospitals, showrooms, buses, railway stations, airports, etc.

Connections

Connection from the Ultrasonic Sensor (HC-SR04) to the Arduino board

In the sensor it has the following four pins; they can work under the process of the receiving and the sending of the signal.

Vcc in the Ultrasonic Sensor can be connected to the Arduino board of the 5V of Vcc.
Triger in the Ultrasonic Sensor can be connected to the Arduino board of the digital pin 12.
Echo pin the Ultrasonic Sensor can be connected to the Arduino board of the digital pin 08.
Gnd in the Ultrasonic Sensor can be connected to the Arduino board of the Gnd.

Connection from LCD Screen to the Arduino board

The LCD screen can have the following four pins.

The Vcc can be connected to the vcc of the Arduino board.
The Gnd can be connected to the Gnd of the Arduino board.
The SDA can be connected to the Arduino board of the analog pin A4 .
The SCL can be connected to the Arduino board of the analog pin A5.

Before uploading the program add the library:

Liquid crystal
I2CAddr0x3F

Programming

#define trigPin 12
# define echoPin 8
//Flashing LED on Arduino board
# define LEDPin 13
//LCD
# include < Wire.h >
#include < LCD.h >
#include < LiquidCrystal_I2C.h >
#define I2C_ADDR 0x3F
// Define I2C Address where the PCF8574A is
# define BACKLIGHT_PIN 3
# define En_pin 2
# define Rw_pin 1
# define Rs_pin 0
# define D4_pin 4
# define D5_pin 5
# define D6_pin 6
# define D7_pin 7
int n = 1;
LiquidCrystal_I2Clcd(I2C_ADDR, En_pin, Rw_pin, Rs_pin, D4_pin, D5_pin, D6_pin, D7_pin);
void setup()
{
Serial.begin(9600);
pinMode(trigPin, OUTPUT); //The transmit pin of the ultrasonic sensor
pinMode(echoPin, INPUT); //The receive pin of the ultrasonic sensor
pinMode(LEDPin, OUTPUT); //The LED of the Arduino
lcd.begin(20, 4);
//Size of LCD
// Switch on the backlight
lcd.setBacklightPin(BACKLIGHT_PIN, POSITIVE);
lcd.setBacklight(HIGH);
lcd.home(); // go home
}
void loop()
{
int duration, distance;
digitalWrite(trigPin, HIGH);
delayMicroseconds(100);
digitalWrite(trigPin, LOW);
duration = pulseIn(echoPin, HIGH);
distance = (duration / 2) / 29.1;
lcd.clear();
lcd.setCursor(0, 0);
lcd.print("Distance from object");
lcd.setCursor(0, 1);
lcd.print(distance);
lcd.print("cm");
if (distance >= 15)
{
lcd.setCursor(0, 4);
lcd.print("Safe Zone :)");
digitalWrite(LEDPin, HIGH);
delay(500);
digitalWrite(LEDPin, LOW);
delay(500);
}
else
{
lcd.clear();
lcd.setCursor(0, 0);
lcd.print("STEP AWAY!!!");
lcd.setCursor(0, 1);
lcd.print("STEP AWAY!!!");
lcd.setCursor(0, 2);
lcd.print("STEP AWAY!!!");
lcd.setCursor(0, 3);
lcd.print("STEP AWAY!!!");
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
delay(50);
digitalWrite(LEDPin, HIGH);
delay(50);
digitalWrite(LEDPin, LOW);
//That really long repeat is to allow the LED pin on the Arduino
}
}

Explanation

In this case, it can send and receive a signal from the ultrasonic sensor, when the object is near it can be displayed in the LCD screen.

When the object is near it can detect the SAFE ZONE message in the LCD screen.

When the object is a way it can detect the STEP AWAY message in the LCD screen.

Output

Figure 3:Output